How to Connect a Security Camera to a TV: 3 Ways That Actually Work

A TV is often the screen that's already in the room — at the front counter, in the back office, in the guard booth. So it's a fair question: can you just plug a security camera into it?

Sometimes yes. Often no, not directly. It depends on what kind of camera you have and what inputs the TV has.

Here's how to tell which situation you're in, and what to do about each one.

Why Most Cameras Don't Plug Straight Into a TV

Security cameras that use coax cable end in a BNC connector — a small round twist-lock plug. Televisions don't have BNC inputs. They have HDMI, and sometimes an older composite (yellow RCA) jack.

So the physical connector is the first problem. The second problem is the signal itself: HD-over-coax cameras send video in formats a TV cannot read — TVI, AHD or CVI. Even with an adapter that makes the plug fit, the TV won't display those formats.

That's why a simple "BNC to RCA" plug adapter usually fails with modern cameras. It changes the connector, not the signal.

Three Ways to Get a Camera Onto a Screen

Option 1: Camera → DVR → TV (HDMI)

Camera --coax--> DVR --HDMI--> TV

This is the standard setup and the only one of the three that also records.

The DVR reads the camera's coax signal, converts it, and outputs HDMI that any TV accepts. You also get multi-camera split screen, playback, motion recording and remote viewing on a phone.

Choose this when: you need recording, more than one camera, or playback of past events. For almost every real installation, this is the right answer.

Option 2: Camera → Video Converter → TV (HDMI)

Camera --coax--> Converter --HDMI--> TV

A BNC to HDMI video converter takes the camera's coax signal and outputs HDMI. No recorder involved.

The SVD 4K BNC to HDMI converter accepts TVI, AHD, CVI and CVBS input and outputs 1080P HDMI. It also has a BNC loop output, so the same camera signal can continue on to a DVR or a second display.

Choose this when: you want one camera on one screen for live viewing only — an entrance view at a reception desk, a gate camera on a break-room TV, a bench setup for testing. Remember: there is no recording in this path. If something happens, there's no footage to go back to.

Option 3: Camera → Security Monitor (BNC)

Camera --coax--> Security Monitor

A purpose-built security monitor accepts the coax signal directly, so there's no converter and no TV involved.

The 19.5" 5MP BNC monitor and the 23.6" 5MP BNC monitor both take HD-TVI and AHD up to 5MP, CVI up to 4MP, and standard CVBS analog — plus HDMI for a DVR, and BNC loop out to pass the signal onward.

Choose this when: the display is going to run continuously. These are built for long operating hours and recover automatically after a power interruption, which a consumer TV may not do.

What About an Old Analog Camera?

If the camera is standard-definition analog (CVBS, often labeled 700TVL, 800TVL or 1000TVL) and the TV still has a yellow composite RCA input, a simple BNC-to-RCA adapter can work.

This only applies to plain analog video. If the camera is 1080p or higher over coax, it is not CVBS, and this shortcut will not produce a picture.

Which Path Fits Your Situation?

What You Need Best Path
Recording and playback DVR to TV over HDMI
Several cameras on one screen DVR to TV over HDMI
One camera, live view only, TV already in place BNC to HDMI converter
A screen that runs all day BNC security monitor
Testing cameras during installation Security monitor or CCTV tester
Old CVBS analog camera, TV has yellow RCA input BNC-to-RCA adapter

Before You Buy Anything

  1. Identify the camera format. TVI, AHD, CVI, or plain CVBS analog? The label or model number usually says.
  2. Check the camera resolution. 1080p, 5MP, or TVL-rated analog?
  3. Check what inputs the TV actually has. HDMI only, or is there a composite input too?
  4. Decide whether you need recording. If yes, the answer is a DVR, not a converter.

The Bottom Line

A TV can display security camera video, but rarely by plugging the camera straight into it. Something in between has to translate the signal: a DVR if you need recording, a converter if you only need a live picture, or a security monitor if you'd rather skip the TV entirely.

Not sure which one fits your system? Browse SVD video converters or compare BNC security monitors — and if you can send us the camera model, our California team can help confirm compatibility.

Back to blog